|
|
|
| Roll-up Frames |
|
| Essential to the structure of the self
supporting system, the roll-up frame is design to maximise strength
and integrity while minimising space. The 5cm (2”) return
offers a stronger frame suited for roll-up door or Z-frame swing
door installations. Single roll-up frames 15.2cm to 30.5cm (6”
to 12”) and double roll-up frames 30.5cm to 61cm (12”
to 24”) are made of hot dipped galvanized 0.81mm (20 gauge)
steel. Glossy white, white or galvalume are the colours in which
these frames are available. All bases, channels and angles and fasteners
necessary to secure the frames to the exterior walls, floors and/or
ceilings are included with the frames. |
|
| |
Corrugated
Swing Door |
 |
Our swing
door has revolutionised the industry. With reinforced solid square
tube cross braces and 7.6cm (3”) wide vertical stiles, this
door is far superior to any others in the industry. Our latch
with magnetic slide that is designed for an optional cylinder
is factory installed on the swing. Available in any of the 0.4mm
(26 gauge) colours, the system and swing make an attractive compliment
or alternative to roll-up doors. |
| Secure Wall |
|
| The non-load bearing wall
divider is manufactured in 50.8cm (20") wide sections that
lock together without the use of exposed screws. It is installed
vertically to minimise dust. All channels and angles necessary to
install secure wall are included. Colours available are glossy white
and white. |
|
| |
Midspan |
 |
This hemmed 0.81mm (20 gauge) channel
further enhances the strength and integrity of our hallway systems.
Offering additional support without having to utilize load bearing
walls, this bracing is available in glossy white, white or galvalume.
|
| Mesh |
|
| A cost effective method of
keeping your tenant's possessions safe is the mesh and mesh angle
stretched over the storage units. The 5cm x 5cm-1.29mm thick (2”
x 2” – 16 gauge) mesh provides security between units
while still allowing for adequate lighting and air flow inside each
unit. |
|
| |
Corrugated
Filler Panel |
 |
An economical
alternative to a flush header is the corrugated filler panel.
This 0.4mm (26 gauge) component is used in the same manner as
the flush header—to enclose the space between the door and
top of the hallway. However, unlike the flush header panel, the
filler panel can be manufactured in any of the door colours to
accent the hallway or roll-up doors. All channels and angles necessary
to install the filler panel are included. Top angle is considered
an accessory. |
| Kick Plates |
|
| Kick plates are installed
to protect the bottom of your hallway walls from scratches and dents
that may occur as tenants move their belongings into a unit. These
0.81mm (20 gauge) galvalume pieces are furnished hemmed on both
the top and bottom. Even though this is typically manufactured 30.5cm
(12”) tall in 3 metre (10’) lengths, custom sizes can
be accommodated. The value of the kick plates is tremendous considering
the wear and tear they take in order to keep the self storage facility
attractive long after “the new” has worn off. |
|
| |
Corner
Gaurds |
 |
Corner
Guards are utilised to help protect your hallway corners from
scratches, dents and dings that occur as tenants transport their
belongings down the hallways to their unit. As a standard component
of the hallway system, the 7.6cm x 7.6cm-0.81mm thick (3”
x 3” – 20 gauge) corner guards are hemmed on both
sides and are available in galvalume, white or glossy white. The
optional mitered corner guard that further enhances the aesthetics
of the hallway system is available for corners where an extended
turning radius is desired. |
| Corawall Hall Partition |
|
| An alternative to corrugated
secure wall, these 30.5cm (12”) self aligning panels interlock
so that there are no exposed screws or edges except where attached
at the top channel. Top and bottom channel included provides additional
strength for supporting panels. An added insurance, the Protective
Package is available to keep these walls dent and ding free once
installed. |
|
| |
Soffit |
 |
Hallway,
light and entry soffit make finishing the ceiling and entrance
of a storage facility economical and yet attractive. The different
soffit types provide a clean finished look to the hallway and
maximise lighting which is appealing to potential customers. |
| Unit Partition |
|
| Like the hallway secure wall,
unit partition is installed vertically. This 0.4mm (26 gauge) galvalume
wall is much more economical than sheet rock or wooded studs while
it still provides the necessary level of security you come to expect
in a wall. All channels and angles necessary to install the unit
partition included. |
|
| |
Headers |
 |
Manufactured
out of 0.81mm (20 gauge) material, the header encloses the area
between the top of the door and top of the hallway system creating
a smooth contemporary look to the flush hall system. It provides
for a clean transition from wall to ceiling when using the light
soffit or solid ceiling and maximises light reflection. All angle
and fasteners required for install are includes in the price of
the header panel. Colours available are white, glossy white and
galvalume. |
|
